METRIC-8 THREADING SETUPS
         For The KNAELL Threader For The
                        TAIG Lathe

Pulley Setups for Cutting Listed Pitches Using 14/11mm Pitch Leadscrew And 11 Tooth Pulley On Spindle (N1 Position).  The METRIC-8 Set Comprises 8 Pulleys of 10, 14, 15, 18, 20, 24, 25,& 28 Teeth.  Thread Pitch is in Millimeters(mm).

       ---------- RH Threading ---------    - LH Thd'g -
       Pitch    N1  N2  N3  N4   B12 B34     N5  B12 B34
       0.200    11  25  10  28   50  45      14  60  50  
       0.250    11  20  10  28   45  50      14  60  50  
       0.280    11  25  14  28   45  50      15  60  50  
       0.300    11  25  15  28   45  50      14  60  50  
       0.350    11  20  14  28   45  50      15  60  50  
       0.360    11  25  18  28   45  50      14  60  50  
       0.375    11  20  15  28   45  50      14  60  50  
       0.400    11  25  20  28   45  50      18  60  50  
       0.420    11  20  15  25   45  50      14  60  50  
       0.450    11  20  18  28   45  50      15  60  50  
       0.480    11  25  24  28   45  50      18  60  50  
       0.500    11  14  10  20   50  45      18  60  45  
       0.525    11  20  18  24   45  50      15  60  50  
       0.600    11  15  18  28   45  50      20  60  45  
       0.625    11  20  25  28   45  50      24  60  45  
       0.700    11  15  18  24   45  50      20  60  45  
       0.720    11  14  18  25   45  50      20  60  45    
       0.750    11  14  18  24   45  50      20  60  45  
       0.800    11  14  20  25   45  50      24  60  45  
       0.840    11  15  18  20   45  50      24  60  45  
       0.875    11  10  15  24   45  50      22  60  45  
       0.900    11  14  18  20   45  50      24  60  45  
       0.960    11  14  24  25   45  50      28  65  50  
       0.980    11  10  14  20   45  50      24  60  45  
       1.000    11  10  20  28   45  60      25  60  50  
       1.050    11  10  18  24   45  50      25  60  45  
       1.120    11  15  24  20   45  50      25  60  45  
       1.200    11  14  18  15   45  50      20  60  45  
       1.250    11  10  25  28   45  60      30  65  50  
       1.500    11  10  15  14   45  50       0  60  45   
Note:
N1, N2, N3,& N4 Pulleys are the same for RH and LH Threading.
The .96 LH setup requires a 65 tooth belt.  
Calculation: Pitch = (14/11)*(11*N3)/(N2*N4)
Pulleys are numbered consecutively through drive train and belt B12 
couples N1 to N2; belt B34 couples N3 to N4.
B12 is belt length running between N1 and N2; Similarly for B34